La Cornue Electric Range E6 Error: Bake Element Open Circuit
La cornue electric range e6 error: Overview La cornue electric range e6 error — this page covers the causes, symptoms, safe checks, and repair-cost guidance drawn from La Cornue owner documentation and certified service records. What Does the E6 Error Code Mean? The E6 error code on La Cornue electric ranges specifically indicates an open […]
~25%
DIY Fixable
From $220
Typical Repair Cost
1–2 hrs
Pro Repair Time
Quick Assessment
Answer to continue safely
Is it safe to keep using?
Maybe. Broil mode and cooktop elements remain safe to use while E6 is active, as they operate on independent circuits. However, do not use bake mode — the element circuit has an open fault, and depending on the cause, forcing bake mode could stress the control board relay. Schedule repair before relying on the oven for baking.
Can I reset the code?
Yes. A power cycle will clear the E6 display, but the bake element circuit remains broken. The code will return whenever bake mode is activated. The element must be replaced to restore full oven function.
When to stop immediately?
Stop if you notice: If you see a visible break or burn on the element surface, do not attempt to use bake mode under any circumstances — the broken element can arc inside the oven cavity., If a broken terminal connection is visible, disconnect power and do not use the oven until the terminal is properly repaired..
Symptoms You May Notice
Oven bottom does not heat during baking
Food placed in the oven cooks unevenly or not at all — the top of the oven may warm from convection or the broil element, but the bake element produces no heat.
E6 code displayed when oven is set to bake
The fault code appears specifically when bake mode is selected, while broil mode may still function normally if that element is intact.
Oven takes significantly longer to preheat
Before the E6 code appears, the oven may seem to preheat but take two to three times longer than normal, relying only on convection or radiant heat from other sources.
Visible damage to the bake element surface
Inspection of the bake element on the oven floor (or under the bake element cover) reveals a crack, blister, or burnt hole in the element's surface.
Possible Causes
Burned-out bake element
The bake element's resistance wire has failed at a point along its length, creating an open circuit. The element must be replaced.
DIY PossibleBroken or disconnected element terminal
One of the two element terminal connectors inside the oven cavity has broken off or pulled loose from the element end fitting.
Requires ProfessionalFaulty element relay on control board
The relay that sends power to the bake element has failed open, so the element never receives voltage regardless of its own condition.
Requires ProfessionalSafe Checks You Can Do
-
1
Visually inspect the bake element
With the oven cooled and the circuit breaker off, remove oven racks and visually inspect the bake element. Look for a visible break, crack, blister, or burn hole anywhere along the element.
On hidden bake element models, the bake element is under a smooth floor panel — look for signs of scorching or warping on the panel surface instead.
-
2
Check the element terminal connections
Look at the two points where the bake element connects to the oven cavity wall. The element terminals should be firmly seated and not loose or visibly cracked.
Do not attempt to push a broken terminal back into place — loose 240V element connections are a serious fire and shock hazard.
-
3
Test broil mode independently
After a power cycle, test broil mode only (not bake). If broil works normally, the fault is isolated to the bake element circuit — confirming E6 is a bake-specific issue and not a broader board or wiring fault.
A working broil element confirms the control board and main element wiring are functional, pointing directly to the bake element or its relay as the fault.
When to Call a Professional
Contact a qualified technician if:
- Resistance testing across the bake element terminals (typically 20–50 ohms for a healthy element; infinite ohms for an open circuit) confirms whether the element needs replacement.
- Element replacement on La Cornue's recessed or hidden-bake models may require removal of the oven floor panel, which should be handled by a trained technician to avoid damage.
- If the element tests good but E6 persists, the bake element relay on the control board must be tested — board-level relay diagnosis requires professional service.
Need Professional Help?
Find qualified technicians in your area for proper diagnostics and repair.
Electric Range Repair Service Schedule Appointment